FENIX WT26RM 2500 lm Working lamp

The Fenix WT26RM is a rechargeable work light that will not leave you in the dark even during the most demanding work. The remote spotlight shines up to 2500 lumens and reaches a distance of 362 meters.

The wide spotlight with high color rendering (CRI ≥90) and the additional red light are suitable for the workshop, home and outdoors. The innovative combination of a rotary and electronic switch makes the control very fast.

Package contents: WT26RM light, ARB-L21-5000 V2.0 battery, USB-C charging cable, spare O-ring, manual, warranty card

1. Three light sources in one light
   Remote spotlight with 2500 lumens, wide spotlight with 600 lumens with LED with high color rendering (CRI ≥90) and red light with 40 lumens and 3 Hz flashing. You can choose the light by simply turning the switch.
2. Free hands while working
   The 360° rotatable handle with integrated strong magnet allows the light to be easily attached to iron surfaces. The flashlight can withstand a drop from a height of 1 meter and has an IP66 rating.

• 21700 battery with 5000 mAh capacity in the package
• Charging via hidden USB-C connector
• Five-level battery status indicator
• Overheat protection
• Last mode memory
• Parameter measurement: according to ANSI/PLATO FL 1
• Handle: 360° rotatable, with integrated magnet
• Memory: switches to the last set mode (except for the red light mode)

Light modes:

Distant beam: 2500 lm (3 h 58 min) – 1000 lm (5 h 31 min) – 350 lm (8 h 37 min) – 100 lm (29 h 49 min)
Wide beam: 600 lm (3 h 10 min) – 250 lm (11 h 57 min) – 30 lm (69 h 21 min)
Red light: 40 lm (15 h 58 min), 3 Hz flashing

Specifications:

Range: distant reflector 362 m (32,822 cd), wide reflector 54 m (734 cd), red light 11 m (30 cd)
Power supply: one Li-ion battery 21700, 5000 mAh (included in the package)
Max. battery dimensions: diameter 21.8 mm, length 77.0 mm
Charging: hidden internal USB-C connector, approx. 3.5 hours for a fully discharged battery
Indication: five LEDs for battery status, low voltage warning
Overheat protection: above 60 °C, reduces power and after cooling gradually increases it again
Material: durable plastic and aluminum alloy
Resistance: IP66 (heavy rain), drop from 1 m height
Dimensions: 12.2 × 5.6 × 4.0 cm (including handle)
Weight: 241 g (including battery)

LEDs: powerful LED for the distant beam (cold white), LED with high color rendering index CRI ≥90 for the wide beam (warm white), red LED; all 50,000 hours of life

Using the Fenix WT26RM charging flashlight
Turning on/off and switching between power modes – When the rotary switch is in the locked position (lock icon), rotate it to any other mode in the order of Locked ↔ Distant beam ↔ Wide beam ↔ Red light. The power of the activated reflector is cyclically switched by pressing the button, which is on the side of the rotary switch. In the distant beam mode: Low – Medium – High – Turbo. In the wide beam mode: Low – Medium – High. In the red light mode, it switches between continuous and flashing light. When the flashlight is unlocked (the rotary switch is in a position other than locked), press and hold the electronic switch for 0.5 seconds to turn it on or off.
Changing the battery – Unscrew the flashlight battery cover and insert the battery with the positive (+) pole facing inwards. Then, fully tighten the cover again.
Battery charge level indicator – When the flashlight is turned off, briefly press the electronic switch to activate the LED charge level indicator for 3 seconds. Five lit green LEDs indicate 100-80%, four 80-60%, three 60-40%, two 40-20%, one lit green or flashing red indicates 20-1% and a critically discharged battery.
Low battery warning – If the battery voltage drops below the set level, the flashlight will automatically switch to a lower mode until it reaches the lowest power. After reaching the lowest power, the battery charge level indicator will start to flash red to remind you to recharge or replace the battery.

Charging the Fenix WT26RM flashlight
Turn off the dust cover and connect the USB-C charging cable to the charging port of the flashlight. During charging, the green indicator lights on the flashlight will flash. Five lit green indicators mean that charging is complete. After charging is complete, carefully seal the dust cover again. The normal charging time is approximately 3.5 hours with a 5 V/2 A (10 W) USB power source for a completely discharged flashlight. You can use the flashlight while it is charging.

Warning
Do not disassemble the sealed parts of the flashlight yourself, as this will void the warranty.
Remove the battery from the flashlight if you are not going to use it for a long time, or lock the flashlight with the rotary switch to prevent accidental activation.
Regular cleaning of the electrical contacts ensures trouble-free operation of the flashlight, as dirty contacts can cause the flashlight to flicker, flash intermittently or not to light up at all for the following reasons:
- The battery is discharged. Charge it or replace it with a charged one.
- The electrical contacts inside the flashlight are dirty, clean them with a cotton swab dipped in alcohol.