FENIX PD32 V2.0 - LED flashlight

The sixth generation of the Fenix PD32 V2.0 flashlight offers an extreme light output of up to 1200 lumens (ANSI) and an impressive range of up to 395 meters. The superior range (considering the size of the flashlight) was achieved by using OSRAM's top-of-the-line KW CSLPM1.TG LED, which produces a very well-focused cone.

The flashlight can be powered by two disposable CR123A batteries or one high-capacity Li-ion 18650 battery. The Fenix PD32 V2.0 features four different light modes, allowing you to choose between high power, long lasting (up to 82 hours) and flash mode for attention grabbing and emergency situations.

The strobe can be quickly activated from the off state by holding down the tactical button for half a second. The PD32 V2.0 impresses not only with its compact size and great performance, but also with the ability to attach the Fenix AER-02 cable switch. Therefore, we can recommend it for use in security forces as well as general outdoor and hunting use.

All flashlight parameters (lumen output, battery life, waterproof, range and shock resistance) are measured in accordance with ANSI/NEMA FL 1-2009.

Package contents: flashlight, wrist lanyard, belt pouch and replacement o-ring. Batteries not included.

Warranty: 5 years

Parameters:

• Uses the latest version of OSRAM KW CSLPM1.TG high-performance LED with a lifetime of 50,000 hours.
• Four lighting modes
• Duration times are measured with a rechargeable 18650 Li-ion battery with 3500mAh capacity.
• Digitally controlled for constant brightness.
• Two 3V disposable CR123A batteries or one rechargeable 18650 Li-ion battery can be used for power.
• Because of the mechanical protection against reverse polarity, the batteries must have a protruding positive terminal. Therefore, older Fenix batteries with a flat plus pole cannot be used.
• The flashlight can be used on long guns with a suitable mounting.
• Smooth parabolic reflector for a light cone with a range of 395 meters (39,000 cd).
• Bottom surface - Type III hard anodized.
• Resistant to drops from a height of 1 meter.
• The flashlight has memory and will always turn on in the last mode set (not valid for flash mode).
• Light-gauge threads with increased wear resistance.
• Substantial surface grooves for better grip, design prevents the flashlight from rotating on uneven surfaces.
• Waterproof and dustproof to IP68 standard (tested underwater at a depth of 2 meters for 30 minutes).
• Removable steel clasp with black finish.
• Hardened ultra clear glass lens with anti-reflective coating.
• Tactical switch at the end of the flashlight (momentary on/off function).
• Wrist lanyard, belt pouch and spare o-ring are included with the flashlight.
• Batteries are not included.

Lighting Modes: 1200 lumens (2.66 hours) -> 350 lumens (5.3 hours) -> 30 lumens (82 hours) -> strobe (1200 lumens).

Wattage: 1200 lm
Range: 395 m
Dimensions :12.94 cm (length) x 2.54 cm (reflector diameter) x 2.36 cm (body diameter)
Weight: 82 grams (without batteries)
Material: aerospace hardened aluminum

Use
Press the tactical button on the end of the flashlight to turn on, press the button to activate immediately. The flashlight remembers the last selected mode (except strobe). Light modes (except strobe) can be cycled by pressing the button. To activate the strobe, hold the button fully down for 0.5 seconds (also possible from off). Pressing the button returns the flashlight to its original mode. Pressing the button turns the flashlight off.
Intelligent overheat protection - Since the flashlight reaches a high output of 1600 lumens, it does experience a temperature rise. If the temperature exceeds 60°C, the power is automatically reduced to approx. 500 lumens. Once the temperature drops below 60°C, the highest power output can be used again.
Battery Low Warning - the flashlight automatically switches to the lowest mode and flashes 3 times every five minutes.

Warning
Do not disassemble the sealed part in the head of the flashlight by yourself, it will violate the warranty.
Use only high quality 3V CR123A batteries and 18650 Li-ion batteries to avoid damaging the flashlight, for example, due to battery leakage.
If the protective rubber rings appear damaged after prolonged use, replace them. The rings should also be lubricated to prevent erosion of the rubber. By following these rules, the flashlight will be properly protected against water.
If the flashlight flickers, does not switch to higher power modes, or does not light up, it may be due to one of the following reasons:
Batteries are almost dead - replace them.
The contacts inside the flashlight are clogged - clean them with a cotton swab dipped in alcohol.
The head, body or back of the flashlight is loose - add lubricant to the sealing rings and tighten both the head and the end of the flashlight firmly.