FENIX E20 V2.0 (350 lumenů) - LED flashlight

The latest generation of the Fenix E20 V2.0 LED flashlight offers a high lumen output of up to 350 lumens (ANSI) and a range of up to 126 meters. This version offers simple operation and four levels of light output with a run time of up to 200 hours. Both control and switching are handled by the end button.

It uses two commercially available pencil batteries for power, of course disposable and rechargeable batteries can be used. A unique innovation is a special collimator that creates a light cone with a range of 126 meters. The collimator is made with technology used in the auto industry and is only 3 millimeters high, less than half the height of commonly used optics.

Thanks to its length of only 127 millimeters and weight of 42 grams (without batteries), it can be carried at all times. This flashlight is an ideal light tool with an excellent ratio of high performance, quality and price.

All flashlight parameters (lumen output, battery life, waterproof, range and shockproof) are measured in accordance with ANSI/NEMA FL 1-2009. The Fenix E20 V2.0 flashlight replaces the older Fenix L2T V2.0, Fenix E20 and Fenix E21 models.

Package Includes: flashlight, wrist lanyard, replacement o-ring and two alkaline batteries

Can be purchased: AOD-S diffuser, AOT-S traffic cone, Fenix swivel belt holster, Fenix bike mount, strap for using the flashlight as a headlamp or ALP-MT case, LockBlocks bike mount, BikeBlock bike helmet mount

Specifications:

• A modern Luminus SST-20 LED with a lifetime of 50,000 hours is used
• Four power modes
• Uses two pencil batteries (AA type - alkaline, lithium or rechargeable NiMH)
• Cheap and widely available AA batteries
• Energizer L91 Ultimate Lithium pencil batteries provide the longest battery life
• Protection against accidental insertion of the battery in reverse (reverse polarity)
• Intelligent overheat protection
• Electronics with digital constant power control
• Battery reverse insertion protection
• Made of T6 aircraft hardened aluminum
• Resistant to falls from a height of 1 meter
• Bottom surface - Type III hard anodized
• Substantial surface grooves for better grip
• Solid clip for safe and easy carrying of the flashlight (removable)
• Special super-thin collimator only 3 mm high
• Waterproof and dustproof to IP68 standard

Power Modes:
measured with rechargeable 1900mAh NiMH batteries: 350 lumens: (1.5 hours)-> 150 lumens (5.5 hours)-> 30 lumens (34.5 hours)-> 5 lumens (140 hours)
measured with included alkaline batteries: 350 lumens (3.75 hours)-> 150 lumens (11.25 hours)-> 30 lumens (93.5 hours)-> 5 lumens (200 hours)</p

Material: aerospace grade T6 hardened aluminum
Dimensions: 12.7 cm (length) x 1.68 cm (body diameter) x 2.1 cm (head diameter)
Weight: 42 grams (without batteries)
Lumen output: 350 lumens
Range: 126 m

Using the Fenix E20 V2.0 LED Flashlight
To turn on, press the switch located on the end of the flashlight. The flashlight will always turn on in the lowest mode. When the flashlight is on, you can change power modes at any time by pressing the button (cycles through low - medium - high - turbo).
Intelligent overheat protection - if the flashlight temperature rises above 58°C, it will automatically start to reduce power in gradual steps of 1% every second until the power is reduced to 150 lumens. Once the lamp temperature drops below 58°C, the output will automatically increase to the original level again. Operation at the highest power mode is thus not limited by time, but only by temperature.

Battery low warning
When the battery voltage drops below the set level, the flashlight will automatically reduce power. When the batteries are low, only the lowest power mode will be available.

Caution
Do not disassemble the sealed part in the head of the flashlight yourself, it will violate the warranty.
Remove the batteries from the flashlight if they are dead. Especially with disposable batteries, there is a risk of draining them and damaging the flashlight.
If the protective rubber rings appear damaged after prolonged use, replace them. The rings should also be lubricated to prevent erosion of the rubber. By following these rules, the flashlight will be properly protected against water.
If the flashlight flickers, does not switch to higher power modes, or does not light up, it may be due to one of the following reasons:
The batteries are almost dead - replace them.
The contacts inside the flashlight are clogged - clean them with a cotton swab dipped in alcohol.
The back of the flashlight is loose - add lubricant to the sealing rings and tighten.